Railroad or railway tracks are used on railways, which, together with railroad switches (points), guide trains without the need for steering. Tracks consist of two parallel steel rails, which are laid upon sleepers (or cross ties) which are embedded in ballast to form the railroad track. The rail is fastened to the sleepers with rail spikes for wooden sleepers or Pandrol clips for cement or concrete sleepers.Rails, being made of steel, can carry heavier loads than any other material.Sleepers spail tracks are normally laid on a bed of coarse stone chippings known as ballast, which combines resilience, some amount of flexibility, and good drainage; however, track can also be laid on or into concrete (this is called slab track).Across bridges track is often laid on sleepers across longitudinal timbers.
Apart from collision, a major possible accident is derailment.

Railway rail
Unlike other uses of iron and steel, railway rails are subject to very high stresses and have to be made of very high quality steel. It took many decades to improve the quality of the materials, including the change from iron to steel. Minor flaws in the steel that pose no problems with, say, reinforcing rods for buildings, can lead to broken rails and dangerous derailments when used on railway tracks.

The rails represent a substantial fraction of the cost of a railway line. Only a small number of rail sizes are made by the steelworks at the one time, so a railway must choose the nearest suitable size. Worn heavy rail from a mainline is often cascaded down to branchline, siding, or yard use.Rails are made in a large number of different sizes. Some common European rail sizes include:

40 kg/m (81 lb/yd)
50 kg/m (101 lb/yd)
60 kg/m (121 lb/yd)
Some common North American rail sizes include:

115 lb/yd (57 kg/m)
133 lb/yd (66 kg/m)
136 lb/yd (67 kg/m)
140 lb/yd (69 kg/m)

Rails in Canada, the United Kingdom, and United States are still described using imperial units. The examples in the diagram opposite are 113 and 95 pounds per yard (56 kg/m and 47 kg/m) respectively.Early railroads sometimes used strap-iron rails, which consisted of thin strips of iron strapped onto wooden rails. These rails were too fragile to carry heavy loads, but because the initial construction cost was less, this method was sometimes used to quickly build an inexpensive rail line. However, the long term expense involved in frequent maintenance outweighed any savings.

Axle load
By and large, the heavier the rails and the rest of the track, the heavier and faster the trains on those tracks can be.

Jointed track
rail jointThere are different ways of joining rails together to form tracks. The traditional way of doing this was to bolt railstogether in what is known as jointed track. In this form of track, lengths of rail, usually around 20 metres (60 feet) long, are laid and fixed to sleepers (U.K.) (crossties, or simply ties in North American practice), and are joined to other lengths of rail with strth American railroads until the mid to late 20th century used sections of rail that measured 39 feet (11.9 m) long socar sizes increased, so did rail lengths.Fishplates or joint bars are usually 60 centimetres (2 feet) long, and are bolted through ea which are known as "expansion joints" to allow for expansion of the rails in hot weather. The holes through which the fishplate bolts pass are oval to allow for expansion.British practice was always to have the rail joints on both rails at the same place on each rail, while North American practice is to stagger them.

Because of the small gaps left between the rails, when trains pass over jointed tracks they make a "clickety clack, clickety clack" noise. Unless it is very well maintained, jointed track gives a fairly bumpy and uncomfortable ride, and is unsuitable folines, and sidings. Most railroad track in the United States is still of this type, however, and laid on timber ties; the lower speeds of American railroads make the disadvantages less apparent, and the abundant supply of timber in the United States makes its use for railroad ties much cheaper than in Europe.Jointed track is still extensively used in poorer countries, due to the cheaper construction costs and lack of modernisation of their railway systems.

Continuous welded rail

welded rail jointMost modern railways use continuous welded rail (CWR); in this form of track the rails are welded together, by utilising the thermite reaction, to form one continuous rail that may be several kilometres long. Because there are few joints, this form of track is very strong, gives a smooth ride, and needs less maintenance.
Because of its strength, trains travelling on welded track can travel at higher speeds and with less friction. Welded rails are more expensive rails expand in hot weather and shrink in cold weather. Because welded track has very few expansion joints, if no special measures are taken, it could become distorted in hot weather and cause a derailment.
To avoid this happening welded rails are very often laid on concrete sleepers, which are so heavy they hold the rails firmly in place, and with plenty of ballast to stop the sleepers moving. After new segments of rail are laid, or defective rails replaced (welded sleepers in their expanded form. This ensures that the rail will not expand much further in subsequent hot weather, and because they are firmly fastened, cannot shrink in cold weather either. However if temperatures reach outside normal ranges (i.e. a hotter than usual summer), welded rails can become distorted.

Joints are used in continuously welded rail when necessary; instead of a joint that passes straight across the rail, producing a loud noise and shock when the wheels pass over it, two sections of rail are cut at a steep angle and put together with a gap between them (a breather switch). This gives a much smoother transition yet still provides some expansion room.

Cross-sections of flat-bottomed and bullhead rails.There are several methods used to fasten rail to wooden sleepers / ties. In traditional British practice, cast metal chairs were screwed to the sleepers, which took a style of rail known as bullhead which was somewhat figure-8 in cross-section — wider at top and bottom (known as the head and foot respectively) and smaller in the middle (the web). Keys, which were wedges of wood or sprung steel were then driven in between chair and rail to holde ide of the rail became worn, the rail could be turned over to the unused side, thus extending the rail's lifespan. In practice, bullhead rails have a flat base (narrower than flat-bottomed rail), and the top part has curved edges which fit the profile of themost of the world, Britain now uses flat-bottomed rail (Vignoles rail), which has become the worldwide standard type of rail and, as the name suggests, has a flat base and can stand upright without support. A flat-bottomed rail has a cross-section like that of an upside-down 'T' and is usually held to the sleeper with a baseplate, a metal plate attached to the sleeper, although for cheap construction they can be laid directly onto the sleepers.

A rail clipModern sleepers can be made of reinforced concrete and pressed steel, with rubber pads inserted between the sleeper and rail. This is done for two reasons: to give a smoother ride and to prevent the sleeper shorting the track circuit, a low voltage passed throue Pandrol fastener, named after its maker, which is shaped like a sturdy, stubby paperclip.North American practice normally uses spikes, which are fundamentally very large nails with bent-over heads to clasp the flat-bottomed rail. These are cheaper and simpler to install but can loosen if the tie rots — much more easily than the British chair does. This is mitigated by using very large and solid ties and using rot-proofing preservative.

Track maintenance

Broken railroad tracks in AlaskaTrack needs frequent maintenance to remain in good order, the frequency increasing with higher-speed or heavier trains. This was formerly hard manual labour, including teams of gandy dancers who used levers to force rails back into place on steep turns, correcting the gradual shifting caused by the centrifugal force of passing trains. Currently, maintenance is facilitated by a variety of specialised machines.
The profile of the track is maintained using a railgrinderCommon maintenance jobs include spraying ballast with weedkiller to prevent weeds growing through and disrupting theballast. This is typically done with a special weedkilling train.Over time, ballast is crushed by the weight of trains passing over it, and periodically it needs to be replaced. If this is not done then the tracks become uneven.Broken or worn out rails also need replacing periodically. Mainline rails that get worn out usually have life left in branchline use and are "cascaded" to those branchlines.

U.S. track classes
In the United States, the Federal Railroad Administration has developed a system of classification for track quality. The class a track is placed in determines speed limits and the ability to run passenger trains.
The lowest class is referred to as excepted track. Only freight trains are allowed to operate on this type of trackage, and they may run at speeds up to 10 mph. Also, no more than five cars loaded with hazardous material may be operated within any single train.ClClass 3 track limits freight trains to 40 mph and passenger trains to 60 mph. There is currently a legal battle between Amtrak and the Guilford Rail System over its trackage from Haverhill, MA, to Portland, ME. Amtrak is fighting for the Class 3 trackage to be used to operate its Downeaster at 79 mph.Class 4 track limits freight trains to 60 mph and passenger trains to 80 mph. Most track, especially that owned by major railroads the Union Pacific, Burlington Northern Santa Fe, CSX, and Norfolk Southern is class 4 track. Due to a technicality in law, Amtrak trains are limited to 79 mph on this track.

Class 5 track limits freight trains to 80 mph and passenger trains to 90 mph. The most significant portion of Class 5 track is part of the Burlington Northern Santa Fe's Chicago–Los Angeles mainline, the old Santa Fe main, upon which Amtrak's Southwest Chief can operate at up to 90 mph. This is notable as the only area outside Amtrak-owned trackage or trackage upgraded through state funds where Amtrak trains can operate above 79 mph.Class 6 limits freight trains and passenger trains to 110 mph. Amtrak is currently working with the Iowa Interstate Railroad and the state of Illinois to upgrade a portion of its Chicago, Illinois–Kansas City, Missouri line to Class 6.Class 7 limits all trains to 125 mph. Most of Amtrak's Northeast Corridor is Class 7 trackage.Class 8 limits all trains to 160 mph. A few small lengths of the Northeast Corridor are the only Class 8 trackage in North America.Class 9 trackage limits all trains to 200 mph. There is currently no Class 9 trackage.derSome early rails were made by William Jessop in the 1790s.
he steel mills making early rails often used some of the rails to build the tramways that bought iron ore and coal to those foundries.

It took many decades for weak and fragile iron rails to evolve into the strong and robust steel rails of today. But problems can still occur, such as happened with the Hatfield train derailment in Great Britain on October 17, 2000. The accident involved gauge corner cracking which is now referred to as rolling contact fatigue, as the defect doesn't only occur on corners.

Index page1 page2 page3 page4 page5 San Francisco tour Villa Lighting